Page 1 sur 2

sensors ne démarre pas

Publié : 02 novembre 2009, 17:22
par Loup-des-Neiges
Salut,

après un petit :

Code : Tout sélectionner

yum install lm_sensors.x86_64
Je me lance dans un petit :

Code : Tout sélectionner

sensors-detect
Mais a la fin quand je lance sensors :

Code : Tout sélectionner

No sensors found!
Make sure you loaded all the kernel drivers you need.
Try sensors-detect to find out which these are.
Voici le sensors-detect :

Code : Tout sélectionner

[root@home ~]# sensors-detect
# sensors-detect revision 5291 (2008-06-23 23:40:46 -0700)

This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.

We can start with probing for (PCI) I2C or SMBus adapters.
Do you want to probe now? (YES/no): YES
Probing for PCI bus adapters...
Found unknown SMBus adapter 10de:07d8 at 0000:00:03.1.
Sorry, no supported PCI bus adapters found.

If you have undetectable or unsupported I2C/SMBus adapters, you can have
them scanned by manually loading the modules before running this script.

To continue, we need module `i2c-dev' to be loaded.
Do you want to load `i2c-dev' now? (YES/no): YES
Module loaded successfully.

We are now going to do the I2C/SMBus adapter probings. Some chips may
be double detected; we choose the one with the highest confidence
value in that case.
If you found that the adapter hung after probing a certain address,
you can specify that address to remain unprobed.

Some chips are also accessible through the ISA I/O ports. We have to
write to arbitrary I/O ports to probe them. This is usually safe though.
Yes, you do have ISA I/O ports even if you do not have any ISA slots!
Do you want to scan the ISA I/O ports? (YES/no): YES
Probing for `National Semiconductor LM78' at 0x290...       No
Probing for `National Semiconductor LM78-J' at 0x290...     No
Probing for `National Semiconductor LM79' at 0x290...       No
Probing for `Winbond W83781D' at 0x290...                   No
Probing for `Winbond W83782D' at 0x290...                   No

Some Super I/O chips may also contain sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no): YES
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor'...                   No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Fintek'...                       Yes
Found `Winbond W83627DHG Super IO Sensors'                  Success!
    (address 0x290, driver `w83627ehf')
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor'...                   No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Fintek'...                       No
Trying family `ITE'...                                      No

Some south bridges, CPUs or memory controllers may also contain
embedded sensors. Do you want to scan for them? (YES/no): YES
Silicon Integrated Systems SIS5595...                       No
VIA VT82C686 Integrated Sensors...                          No
VIA VT8231 Integrated Sensors...                            No
AMD K8 thermal sensors...                                   No
AMD K10 thermal sensors...                                  No
Intel AMB FB-DIMM thermal sensor...                         No

Now follows a summary of the probes I have just done.
Just press ENTER to continue:

Driver `w83627ehf' (should be inserted):
  Detects correctly:
  * ISA bus, address 0x290
    Chip `Winbond W83627DHG Super IO Sensors' (confidence: 9)

Do you want to overwrite /etc/sysconfig/lm_sensors? (YES/no): YES
Démarrage de lm_sensors :No sensors found!
Make sure you loaded all the kernel drivers you need.
Try sensors-detect to find out which these are.
                                                           [ÃCHOUÃ]

Re: sensors ne démarre pas

Publié : 02 novembre 2009, 18:05
par nouvo09
Driver `w83627ehf' (should be inserted)
Il semble là le souci. Tu as ce pilote ?

Re: sensors ne démarre pas

Publié : 02 novembre 2009, 18:05
par MarbolanGos
J'ai le même problème.. Donc pas de solution :(

Et je suis en 32 bits

Re: sensors ne démarre pas

Publié : 02 novembre 2009, 20:21
par Loup-des-Neiges
Bha pilote d'origine : /
Et aucun kmod-forcedeth sur les dépôts ><

(Comment savoir le nom du pilote et ou le chercher ? : °)

Re: sensors ne démarre pas

Publié : 02 novembre 2009, 20:32
par nouvo09
A tout hasard voilà ce que j'ai trouve :

http://ubuntuforums.org/showthread.php?t=424302

Re: sensors ne démarre pas

Publié : 02 novembre 2009, 20:57
par Loup-des-Neiges
http://www.centos-fr.org/forums/viewtopic.php?f=15&t=13

(Même serveur)
Me manque juste le pilote de ma carte mère en gros ? (Que je ne trouve pas)
C'est mon 2em bug avec les pilotes x]
Vous n'avez pas un tuto/astuce pour savoir le nom du pilote qui correspond a ma carte mère ?
Que j'essaye de me sortir les papates de la semoule :)

Edite :
http://www.nodeofcrash.com/?p=71
Le lien qu'il donne : http://www.nodeofcrash.com/download/w83 ... os5.tar.gz
Correspond donc bien a ma carte ?

Re: sensors ne démarre pas

Publié : 02 novembre 2009, 21:46
par Arrfab
Loup-des-Neiges a écrit :...
Et aucun kmod-forcedeth sur les dépôts ><
...
Aucune idée pour ta carte mère, mais bien pour le kmod-forcedeth : http://elrepo.org/tiki/Packages
Elrepo.org est un dépôt orienté hardware et exclusivement pour RHEL5/CentOS5/Scientific Linux 5 (collaboration de membres CentOS ;-) )

Re: sensors ne démarre pas

Publié : 03 novembre 2009, 13:36
par Loup-des-Neiges
Arrfab a écrit :Aucune idée pour ta carte mère, mais bien pour le kmod-forcedeth : http://elrepo.org/tiki/Packages
Elrepo.org est un dépôt orienté hardware et exclusivement pour RHEL5/CentOS5/Scientific Linux 5 (collaboration de membres CentOS ;-) )
Ah bien le dépôt :mrgreen:
Un petit :

Code : Tout sélectionner

rpm -Uvh http://elrepo.org/linux/elrepo/el5/x86_64/RPMS/elrepo-release-0.1-1.el5.elrepo.noarch.rpm
Et je test le kmod ;) Merci beaucoup

Edite : [yum install kmod-forcedeth] toujours rien ><
Edite2 : [yum --enablerepo=elrepo-testing install kmod-w83627ehf]

Voila, sensors fonctionne =D

Re: sensors ne démarre pas

Publié : 03 novembre 2009, 16:14
par MarbolanGos
Ah bah si quelqu'un a la solution pour mon cas

Code : Tout sélectionner

# sensors-detect 
# sensors-detect revision 5291 (2008-06-23 23:40:46 -0700)

This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.

We can start with probing for (PCI) I2C or SMBus adapters.
Do you want to probe now? (YES/no): YES
Probing for PCI bus adapters...
Use driver `i2c-i801' for device 0000:00:1f.3: Intel 82801G ICH7

We will now try to load each adapter module in turn.
Module `i2c-i801' already loaded.
If you have undetectable or unsupported I2C/SMBus adapters, you can have
them scanned by manually loading the modules before running this script.

We are now going to do the I2C/SMBus adapter probings. Some chips may
be double detected; we choose the one with the highest confidence
value in that case.
If you found that the adapter hung after probing a certain address,
you can specify that address to remain unprobed.

Next adapter: SMBus I801 adapter at ece0 (i2c-0)
Do you want to scan it? (YES/no/selectively): YES
Client found at address 0x50
Probing for `Analog Devices ADM1033'...                     No
Probing for `Analog Devices ADM1034'...                     No
Probing for `SPD EEPROM'...                                 Yes
    (confidence 8, not a hardware monitoring chip)
Probing for `EDID EEPROM'...                                No
Client found at address 0x52
Probing for `Analog Devices ADM1033'...                     No
Probing for `Analog Devices ADM1034'...                     No
Probing for `SPD EEPROM'...                                 Yes
    (confidence 8, not a hardware monitoring chip)
Probing for `EDID EEPROM'...                                No

Next adapter: NVIDIA i2c adapter 0 at 1:00.0 (i2c-1)
Do you want to scan it? (YES/no/selectively): YES
Adapter cannot be probed, skipping.

Next adapter: NVIDIA i2c adapter 1 at 1:00.0 (i2c-2)
Do you want to scan it? (YES/no/selectively): YES
Adapter cannot be probed, skipping.

Next adapter: NVIDIA i2c adapter 2 at 1:00.0 (i2c-3)
Do you want to scan it? (YES/no/selectively): YES
Adapter cannot be probed, skipping.

Some chips are also accessible through the ISA I/O ports. We have to
write to arbitrary I/O ports to probe them. This is usually safe though.
Yes, you do have ISA I/O ports even if you do not have any ISA slots!
Do you want to scan the ISA I/O ports? (YES/no): YES
Probing for `National Semiconductor LM78' at 0x290...       No
Probing for `National Semiconductor LM78-J' at 0x290...     No
Probing for `National Semiconductor LM79' at 0x290...       No
Probing for `Winbond W83781D' at 0x290...                   No
Probing for `Winbond W83782D' at 0x290...                   No

Some Super I/O chips may also contain sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no): YES
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor'...                   No
Trying family `SMSC'...                                     Yes
Found `SMSC SCH5514D-NS Super IO'                           
    (no hardware monitoring capabilities)
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor'...                   No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Fintek'...                       No
Trying family `ITE'...                                      No

Some south bridges, CPUs or memory controllers may also contain
embedded sensors. Do you want to scan for them? (YES/no): YES
Silicon Integrated Systems SIS5595...                       No
VIA VT82C686 Integrated Sensors...                          No
VIA VT8231 Integrated Sensors...                            No
AMD K8 thermal sensors...                                   No
AMD K10 thermal sensors...                                  No
Intel AMB FB-DIMM thermal sensor...                         No

Sorry, no sensors were detected.
Either your sensors are not supported, or they are connected to an
I2C or SMBus adapter that is not supported. See doc/FAQ,
doc/lm_sensors-FAQ.html or http://www.lm-sensors.org/wiki/FAQ
(FAQ #4.24.3) for further information.
If you find out what chips are on your board, check
http://www.lm-sensors.org/wiki/Devices for driver status.

Re: sensors ne démarre pas

Publié : 01 mars 2010, 22:52
par Loup-des-Neiges
Re-salut ;)

De nouveau le problème sur un SP mini 09 de chez OVH,
Comment savoir le driver qu'il manque a mon serveur ? Pas de "should be inserted" comme précèdent ><
(C'est une installation minimum de CentOS via KVM)

Edite : ah, même configuration que MarbolanGos au dessus !
Edite2: C'est le driver "W83781D" ? Ou un simple "kmod-forcedeth" suffira ?
Edite3: dmidecode : http://pastebin.com/8kpBtgj1

Code : Tout sélectionner

[root@server ~]# sensors-detect
# sensors-detect revision 5291 (2008-06-23 23:40:46 -0700)

This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.

We can start with probing for (PCI) I2C or SMBus adapters.
Do you want to probe now? (YES/no): YES
Probing for PCI bus adapters...
Use driver `i2c-i801' for device 0000:00:1f.3: Intel 82801G ICH7

We will now try to load each adapter module in turn.
Module `i2c-i801' already loaded.
If you have undetectable or unsupported I2C/SMBus adapters, you can have
them scanned by manually loading the modules before running this script.

To continue, we need module `i2c-dev' to be loaded.
Do you want to load `i2c-dev' now? (YES/no): YES
Module loaded successfully.

We are now going to do the I2C/SMBus adapter probings. Some chips may
be double detected; we choose the one with the highest confidence
value in that case.
If you found that the adapter hung after probing a certain address,
you can specify that address to remain unprobed.

Next adapter: SMBus I801 adapter at 0400 (i2c-0)
Do you want to scan it? (YES/no/selectively): YES
Client found at address 0x50
Probing for `Analog Devices ADM1033'...                     No
Probing for `Analog Devices ADM1034'...                     No
Probing for `SPD EEPROM'...                                 Yes
    (confidence 8, not a hardware monitoring chip)
Probing for `EDID EEPROM'...                                No

Some chips are also accessible through the ISA I/O ports. We have to
write to arbitrary I/O ports to probe them. This is usually safe though.
Yes, you do have ISA I/O ports even if you do not have any ISA slots!
Do you want to scan the ISA I/O ports? (YES/no): YES
Probing for `National Semiconductor LM78' at 0x290...       No
Probing for `National Semiconductor LM78-J' at 0x290...     No
Probing for `National Semiconductor LM79' at 0x290...       No
Probing for `Winbond W83781D' at 0x290...                   No
Probing for `Winbond W83782D' at 0x290...                   No

Some Super I/O chips may also contain sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no): YES
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor'...                   No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Fintek'...                       Yes
Found unknown chip with ID 0xb073
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor'...                   No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Fintek'...                       No
Trying family `ITE'...                                      No

Some south bridges, CPUs or memory controllers may also contain
embedded sensors. Do you want to scan for them? (YES/no): YES
Silicon Integrated Systems SIS5595...                       No
VIA VT82C686 Integrated Sensors...                          No
VIA VT8231 Integrated Sensors...                            No
AMD K8 thermal sensors...                                   No
AMD K10 thermal sensors...                                  No
Intel AMB FB-DIMM thermal sensor...                         No

Sorry, no sensors were detected.
Either your sensors are not supported, or they are connected to an
I2C or SMBus adapter that is not supported. See doc/FAQ,
doc/lm_sensors-FAQ.html or http://www.lm-sensors.org/wiki/FAQ
(FAQ #4.24.3) for further information.
If you find out what chips are on your board, check
http://www.lm-sensors.org/wiki/Devices for driver status.