lm_sensors, configuration automatique ne fonctionne pas

Avatar de l’utilisateur
Loup-des-Neiges
Messages : 78
Inscription : 20 octobre 2009, 23:29
Localisation : Cannes (06)
Contact :

lm_sensors, configuration automatique ne fonctionne pas

Message par Loup-des-Neiges » 17 septembre 2011, 02:34

Salut,

Sur un vieux laptop Acer, quand je lance la configuration automatique via la commande "sensors-detect",
aucune configuration ne s'inscrit dans le fichier de configuration. Il en résulte donc un avertissement.

Pas compatible ?

Code : Tout sélectionner

[root@home ~]# sensors-detect
# sensors-detect revision 1.1
# System: Acer Aspire 5100 (laptop)
# Board: Acer Navarro

This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.

Some south bridges, CPUs or memory controllers contain embedded sensors.
Do you want to scan for them? This is totally safe. (YES/no): YES
Silicon Integrated Systems SIS5595...                       No
VIA VT82C686 Integrated Sensors...                          No
VIA VT8231 Integrated Sensors...                            No
AMD K8 thermal sensors...                                   Success!
    (driver `k8temp')
AMD Family 11h thermal sensors...                           No
Intel Core family thermal sensor...                         No
Intel AMB FB-DIMM thermal sensor...                         No
VIA C7 thermal and voltage sensors...                       No

Some Super I/O chips contain embedded sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no): YES
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor'...                   No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Nuvoton/Fintek'...               No
Trying family `ITE'...                                      No
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor'...                   No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Nuvoton/Fintek'...               No
Trying family `ITE'...                                      No

Some hardware monitoring chips are accessible through the ISA I/O ports.
We have to write to arbitrary I/O ports to probe them. This is usually
safe though. Yes, you do have ISA I/O ports even if you do not have any
ISA slots! Do you want to scan the ISA I/O ports? (YES/no): YES
Probing for `National Semiconductor LM78' at 0x290...       No
Probing for `National Semiconductor LM79' at 0x290...       No
Probing for `Winbond W83781D' at 0x290...                   No
Probing for `Winbond W83782D' at 0x290...                   No

Lastly, we can probe the I2C/SMBus adapters for connected hardware
monitoring devices. This is the most risky part, and while it works
reasonably well on most systems, it has been reported to cause trouble
on some systems.
Do you want to probe the I2C/SMBus adapters now? (YES/no): YES
Using driver `i2c-piix4' for device 0000:00:14.0: ATI Technologies Inc IXP SB400 SMBus Controller
Module i2c-dev loaded successfully.

Next adapter: Radeon i2c bit bus DVI_DDC (i2c-0)
Do you want to scan it? (YES/no/selectively): YES

Next adapter: Radeon i2c bit bus VGA_DDC (i2c-1)
Do you want to scan it? (YES/no/selectively): YES

Next adapter: Radeon i2c hw bus MM_I2C (i2c-2)
Do you want to scan it? (YES/no/selectively): YES

Next adapter: Radeon i2c bit bus MONID (i2c-3)
Do you want to scan it? (YES/no/selectively): YES

Next adapter: Radeon i2c bit bus GPIOPAD_MASK (i2c-4)
Do you want to scan it? (YES/no/selectively): YES

Next adapter: SMBus PIIX4 adapter at 8400 (i2c-5)
Do you want to scan it? (YES/no/selectively): YES
Client found at address 0x50
Probing for `Analog Devices ADM1033'...                     No
Probing for `Analog Devices ADM1034'...                     No
Probing for `SPD EEPROM'...                                 Yes
    (confidence 8, not a hardware monitoring chip)
Probing for `EDID EEPROM'...                                No
Client found at address 0x51
Probing for `Analog Devices ADM1033'...                     No
Probing for `Analog Devices ADM1034'...                     No
Probing for `SPD EEPROM'...                                 Yes
    (confidence 8, not a hardware monitoring chip)

Now follows a summary of the probes I have just done.
Just press ENTER to continue:

Driver `k8temp' (autoloaded):
  * Chip `AMD K8 thermal sensors' (confidence: 9)

No modules to load, skipping modules configuration.

Unloading i2c-dev... OK

[root@home ~]# service lm_sensors start
Starting lm_sensors: not configured, run sensors-detect    [AVERTISSEMENT]
[root@home ~]# cat /etc/sysconfig/lm_sensors
#    /etc/sysconfig/sensors - Defines modules loaded by /etc/rc.d/init.d/lm_sensors
# Run sensors-detect to generate this config file
[root@home ~]#
Par avance, merci de votre attention !
Serveur(s) : [home/serveur-1/serveur-2].loup-des-neiges.com
CentOS : 6 CR
Utilisateur des dépôts : RHEL, REMI

Avatar de l’utilisateur
nouvo09
Messages : 2159
Inscription : 20 octobre 2009, 08:14
Localisation : Paris, France

Re: lm_sensors, configuration automatique ne fonctionne pas

Message par nouvo09 » 17 septembre 2011, 08:51

Ben, la réponse est dans la question :
No modules to load, skipping modules configuration.

Unloading i2c-dev... OK
il n'y a pas de sonde détectée donc rien à faire.
C'est pas parce que c'est difficile qu'on ose pas,
c'est parce qu'on ose pas que c'est difficile !

Répondre